Sunday, October 16, 2016


Having fun with raspberry pi 3 and Astro Hat.

********* basic installation ********

fdisk /dev/mmcblk0
unmount and reinsert
looking for the images:
There are a bunch of them...
Only one I have picked this one.
losetup --partscan --find --show /home/jfclere/Downloads/Fedora-Server-armhfp-24-1.2-sda.raw /dev/loop0
mount -r /dev/loop0p3 /tmp/img/
mkfs.vfat /dev/mmcblk0p1
mkswap /dev/mmcblk0p2
mkfs.ext4 /dev/mmcblk0p3
mkdir /tmp/rpi/
mount /dev/mmcblk0p3 /tmp/rpi/
mkdir /tmp/rpi/boot/
mount /dev/mmcblk0p1 /tmp/rpi/boot/
cp -rpv /tmp/img/* /tmp/rpi/
sync (takes ages)
losetup -d /dev/loop0
[root@jfcpc NOTES]# blkid | grep mmcblk0
/dev/mmcblk0: PTTYPE="dos"
/dev/mmcblk0p1: SEC_TYPE="msdos" UUID="DB85-3C4A" TYPE="vfat"
/dev/mmcblk0p2: UUID="5f07dbe9-2619-481e-b0b3-5f37a7f011bf" TYPE="swap"
/dev/mmcblk0p3: UUID="8df2bd5c-4692-4f80-96ec-da2e9697a713" TYPE="ext4"
edit and ajust /tmp/rpi/etc/fstab
/tmp/rpi/boot/cmdline.txt Add
"dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p3 rootfstype=ext4 elevator=deadline rootwait" (configuration stuff).
/tmp/rpi/boot/config.txt (do we need something?...) empty for the moment...
copy the boot and modules
download the firmware:
what is:
it is like (just a zip repo).
dowload and unzip
[root@jfcpc NOTES]# cp -r /home/jfclere/Downloads/firmware-master/boot/* /tmp/rpi/boot/
So (for + and -v7+ no idea how it is choosen)
Once running doing more /proc/cpuinfo:
processor : 0
model name : ARMv7 Processor rev 4 (v7l)
guessing we use the -v7+ ;-)
[root@jfcpc NOTES]# cp -r /home/jfclere/Downloads/firmware-master/modules/* /tmp/rpi/lib/modules/
umount /tmp/rpi/boot/
umount /tmp/rpi/
network: (trying to check it)...
In fact the fedora24 use systemd
/tmp/rpi/etc/systemd/ (there something run at the first boot).
/tmp/rpi/etc/systemd/system/ -> /lib/systemd/system/
/tmp/rpi/lib/systemd/system/systemd-firstboot.service ?
and it run /usr/bin/systemd-firstboot --prompt-locale --prompt-timezone --prompt-root-password
ExecStart=/usr/bin/systemd-firstboot --prompt-locale --prompt-timezone --prompt-root-password
For the curious:
[jfclere@jfcpc ~]$ rpm -qf /usr/bin/systemd-firstboot
nmap -sn
found the PI:
Nmap scan report for pc-151.home (
Host is up (0.047s latency).
MAC Address: B8:27:EB:C1:44:41 (Raspberry Pi Foundation)
scanning it:
[root@jfcpc Downloads]# nmap
Starting Nmap 7.12 ( ) at 2016-09-07 22:15 CEST
Nmap scan report for pc-151.home (
Host is up (0.0044s latency).
Not shown: 998 filtered ports
22/tcp open ssh
9090/tcp open zeus-admin
MAC Address: B8:27:EB:C1:44:41 (Raspberry Pi Foundation)
Nmap done: 1 IP address (1 host up) scanned in 4.60 seconds
Some how the password stuff failed... The stuff still asks :-(
copy my fedora laptop password that helps...
[root@pc-151 ~]# ps -ef | grep tty1
root 343 1 0 18:23 tty1 00:00:00 /bin/bash /usr/libexec/initial-setup/run-initial-setup
root 348 343 12 18:23 tty1 00:00:23 /usr/bin/python3 /usr/libexec/initial-setup/initial-setup-text --no-stdout-log
root 720 696 0 18:26 pts/0 00:00:00 grep --color=auto tty1
In it:
/bin/systemctl disable initial-setup.service (so it remove itself).
and it is a python script...
trying... mount
/dev/mmcblk0p3 on /run/media/jfclere/a440011a-a5ea-4eb7-ae01-95c8cd981673
[root@jfcpc Downloads]# grep ENCRYPT_METHOD /tmp/img/etc/login.defs
echo -n root:Changeit2016 | chpasswd -c SHA512 -R /run/media/jfclere/a440011a-a5ea-4eb7-ae01-95c8cd981673 ?
selinux problems :-( and doesn't work.
echo -n root:Changeit2016 | chpasswd -c SHA512 in PI works...
setting timezone:
ls -lt /usr/share/zoneinfo/Europe/Zurich
rm /etc/localtime
ln -s /usr/share/zoneinfo/Europe/Zurich /etc/localtime
easy :D
Done forget to remove the base fedora kernel components (yum might get funny overrwise)...
dnf remove kernel kernel-core kernel-modules

************** configure wifi *************

The goal is to get a sort of captive portal to run an easy demo, the raspberry is acting as an AP and dhcp server and name server
[root@pc-111 ~]# nmcli device status
eth0 ethernet connected eth0
lo loopback unmanaged --
no wifi.
$ cd /lib/firmware/brcm/
$ curl -O
$ curl -O
iw list
Supported interface modes:
* managed
* AP
it can do AP cool...
dnf install NetworkManager-tui NetworkManager-wifi
Mode <Access Point>
Channel <Automatic>
Security <None>
[X] Never use this network for default route
[X] Require IPv4 addressing for this connection
[X] Automatically connect
From the laptop:
wlp4s0 IEEE 802.11 ESSID:"PI"
Mode:Managed Frequency:2.412 GHz Access Point: B8:27:EB:94:11:14
in PI:
wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether b8:27:eb:94:11:14 txqueuelen 1000 (Ethernet)
hm laptop doesn't get IP?
try dhcp (server?) (give to the PI)
Look to /etc/dhcp/dhcpd.conf
The important:
subnet netmask {
so it listens on
option domain-name "";
option domain-name-servers;
so the name are resolved by the bind of PI.
option routers
so it is the routers for the interface (we can use the PI as router!!!).
Looks nearly OK...
Listening on LPF/wlan0/b8:27:eb:94:11:14/
Sending on LPF/wlan0/b8:27:eb:94:11:14/
ifconfig on the laptop:
wlp4s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet netmask broadcast
nmap -sn (it finds the PI)
[root@jfcpc APACHE-2.4.x]# nmap -sn
Starting Nmap 7.12 ( ) at 2016-09-14 23:41 CEST
Nmap scan report for
Host is up (0.014s latency).
MAC Address: B8:27:EB:94:11:14 (Raspberry Pi Foundation)
Nmap scan report for
Host is up.
Nmap done: 256 IP addresses (2 hosts up) scanned in 32.09 seconds
easy... (connected).
to find the address:
nmap -sn
(doesn't help... well run it as root = better...)
Nmap scan report for pc-111.home (
Host is up (0.0067s latency).
MAC Address: B8:27:EB:7A:A6:98 (Raspberry Pi Foundation)
Nmap scan report for pc-111.home (
Host is up (0.0067s latency).
name server: (based on
yum install bind
listen-on port 53 {; };
allow-query {; };
recursion no;
zone "." IN {
type master;
file "/etc/bind/db.fakeroot";
And in /etc/bind/db.fakeroot:
@ IN SOA ( 1 3h 1h 1w 1d )
* IN A
Don't forget the firewall on the PI:
firewall-cmd --permanent --zone=FedoraServer --add-port=53/tcp
firewall-cmd --permanent --zone=FedoraServer --add-port=53/udp
firewall-cmd --reload

********* Getting tomcat running *********

yum install java should be ready for tomcat).
yum install java maven
git clone
cd tomcatPI/demo
java -jar ./target/demo-1.0-SNAPSHOT-jar-with-dependencies.jar
Don't forget the firewall (again).
firewall-cmd --permanent --zone=FedoraServer --add-port=80/tcp
firewall-cmd --reload

******** Getting Astro Hat examples running ********

HAT: (looks the good one...)
A lot needs to be install gcc/python-devel/gcc-gfortran/redhat-rpm-config (hard to guess this one!) and building takes ages...
libz-devel, jpeg-devel
testing... /root/python-sense-hat/examples
mssing cmake/gcc-c++
in RTIMULib/RTIMULi/build (mkdir ) cmake ... make make install.
in RTIMULib/Linux need qt-devel
in RTIMULib/Linux/python (probably the only one really needed!).
./python-sense-hat/examples/ (works...)
./RTIMULib/Linux/build/RTIMULibCal/RTIMULibCal (to get the RTIMULib.ini to pur in /etc according to the doc).
******* Playing with the 8X8 frame buffer ****
[root@jfcpc java]# pwd
[root@jfcpc java]# java -cp . org.jfclere.tomcatPI.PIFrameBuffer
file is 4096Exception in thread "main" No such device
at Method)
at org.jfclere.tomcatPI.PIFrameBuffer.main(
+++ OK ++++ It can't read it :-(
According to Python code:
from sense_hat import SenseHat
The LED matrix is an RGB565 framebuffer
(more or less working now committed).

********* Sending information to ActiveMQ and consuming it *******

yum install stomppy
install activemq on laptop
check stomp port:
INFO | Listening for connections at: stomp://jfcpc:61613?maximumConnections=1000&wireFormat.maxFrameSize=104857600
INFO | Connector stomp started (we receive something binary UTF8 encoded string).
write a STOMP logic to send message to ActiveMQ (running on my laptop)
write a small jms client to consum the messages from the raspberry

This page is powered by Blogger. Isn't yours?